Off-Grid Solar System Calculator: Panels & Batteries

An off-grid solar system operates completely independently of the electricity grid. It must generate enough electricity during sunlight hours to power your daytime loads and fully charge a battery bank to carry you through the night and cloudy weather. Correct engineering is critical because an undersized off-grid system will leave you in darkness or damage expensive batteries through chronic undercharging.

Typical Off-Grid Load Presets
Continuous Load W
Peak Startup Surge W
Calculated Daily Load kWh
Units
Hours

Days

1 day is standard for sunny plains. 1.5 to 2 days is strongly advised in heavy monsoon or winter fog zones.

Auto-Selected
₹
kW

Off-Grid Solar & Battery Storage Sizer

Insolation, Surge VA & Battery Autonomy Engine

%
1. Calculating daily watt-hours & connected peak surge...
2. Sizing solar PV array with NASA PSH insolation...
3. Sizing deep-cycle battery bank with autonomy days & DoD...
4. Sizing MPPT solar charge controller & off-grid inverter...
Design Assumptions and Calculation Methodology Rates and benchmarks updated: 18 Nov 2026
  • Solar array is oversized by 30% above bare daily consumption. This ensures the solar array can power running daytime loads AND fully recharge the depleted battery bank within the limited peak sunlight window.
  • Battery bank capacity in Ampere-Hours (Ah) accounts for your system DC bus voltage (12V, 24V, or 48V), battery Depth of Discharge (DoD), and inverter conversion efficiency (95%).
  • Depth of Discharge (DoD) limits ensure battery longevity: 60% for C10 tubular lead-acid, 85% for Lithium Iron Phosphate (LiFePO4), and 50% for standard flat-plate lead-acid.
  • Inverter capacity (VA) is sized with a 0.8 power factor to safely handle continuous running wattage and the inductive surge of motors, compressors, and water pumps.
  • Panels and battery prices reflect current Indian manufacturer benchmark rates. Turnkey costs include galvanized iron mounting structures, copper DC cables, AC/DC distribution boxes with surge protection devices (SPDs), and chemical earthing pits.

Off-Grid Solar System Benchmark Sizing Table

Daily Load (Units) Recommended Solar Array Tubular Battery Bank (48V) Indicative Equipment Cost
5 kWh/day 1 kW 183 Ah ₹63,289
10 kWh/day 1 kW 365 Ah ₹66,579
15 kWh/day 1 kW 548 Ah ₹69,868
20 kWh/day 1 kW 731 Ah ₹73,158

Based on tubular C10 batteries with 1 day of autonomy at standard Indian solar insolation (4.7 PSH). Lithium systems have a higher initial capital outlay but deliver a lower levelized cost per kWh over 10 years.

How an Off-Grid Solar System Works in India

An off-grid solar system is a self-sustaining power plant that operates without any reliance on the public electricity grid. The system consists of four primary components: the solar photovoltaic (PV) array, an MPPT Solar Power Conditioning Unit (PCU) or charge controller with an inverter, a deep-cycle battery storage bank, and protective balance-of-system hardware including DC distribution boxes, surge protection devices, and earthing rods.

During daylight hours, solar panels absorb sunlight and generate direct current (DC) electricity. The MPPT charge controller tracks the optimal electrical operating point of the panels, maximizing energy extraction even under partial haze. This power is directed simultaneously to two destinations: running your active appliances through the pure sine wave inverter and charging the battery bank. Once the sun sets or heavy clouds roll in, the system automatically draws stored energy from the battery bank to supply your household AC loads seamlessly.

Engineering Formulas: Sizing Solar Panels and Batteries Correctly

Unlike on-grid systems where the utility grid acts as an infinite virtual buffer, off-grid systems cannot afford sizing guesswork. Sizing the solar array requires accounting for the daily load, location-specific Peak Sun Hours (PSH), system performance ratio, and essential array oversizing. In India, off-grid solar arrays must be oversized by at least 25% to 35% above the raw daily consumption. Without this margin, on cloudy days the array will generate only enough power to operate immediate daytime loads, leaving the battery bank partially drained going into the night.

Battery capacity in Ampere-Hours (Ah) is calculated by taking the daily watt-hours multiplied by required days of autonomy, divided by the product of system DC bus voltage, battery Depth of Discharge (DoD), and inverter efficiency. For instance, powering an 8-unit (8,000 Wh) daily load on a 48V tubular system with 1 day of autonomy requires 8,000 / (48 × 0.60 × 0.95) = approximately 292 Ah at 48V. This translates to two parallel strings of four 150 Ah 12V batteries (8 batteries total).

Tubular C10 vs Lithium (LiFePO4) Solar Batteries in Indian Conditions

Tall tubular lead-acid batteries (specifically C10 solar rated) have historically been the backbone of Indian off-grid installations. They are mechanically resilient, readily available in tier-2 and rural markets, and feature an affordable upfront purchase price. However, tubular batteries have a safe Depth of Discharge of only 60% to 70%, require periodic distilled water replenishment every 3 to 6 months, and provide an operational lifespan of 1,200 to 1,500 cycles (roughly 3 to 5 years). In hot regions such as Rajasthan, Gujarat, and Uttar Pradesh, high ambient summer temperatures accelerate electrolyte evaporation and plate corrosion.

Lithium Iron Phosphate (LiFePO4) has emerged as the premier choice for modern off-grid installations. While lithium batteries cost approximately 2.5 times more upfront per nominal Ah, they allow up to 85% to 90% depth of discharge, achieve 3,500 to 5,000 charge cycles, and require zero maintenance over a 10- to 12-year working life. When evaluated on a 10-year Total Cost of Ownership (TCO) basis, lithium is consistently more economical because a tubular battery bank will need to be replaced twice during the same operational timeframe.

System Bus Voltage: Why 48V Architecture Matters for Medium and Heavy Loads

Selecting the proper DC bus voltage—12V, 24V, or 48V—is one of the most critical electrical engineering decisions in an off-grid setup. As electrical power equals voltage multiplied by current (P = V × I), delivering high wattage at a low system voltage forces extremely high current through the battery cables. For example, running a 2,400-watt load at 12V draws 200 Amperes of continuous direct current. Handling 200 Amperes safely requires thick 50 sq mm copper conductors, heavy-duty industrial busbars, and results in substantial I²R heat and voltage losses.

By elevating the system architecture to 48V (achieved by wiring four 12V batteries in series), the required current for that same 2,400-watt load drops fourfold to just 50 Amperes. This lower amperage allows standard 10–16 sq mm solar DC cables, drastically reduces thermal losses, enhances inverter operating efficiency, and ensures safety against electrical fire risks. As an engineering standard, setups above 1,000 Watts should utilize at least 24V, while setups exceeding 2,000 Watts must always be engineered at 48V.

Government Subsidy Reality: Why Off-Grid Solar Receives No Central Subsidy

A frequent misunderstanding among Indian property owners is whether off-grid solar systems qualify for the central PM Surya Ghar Muft Bijli Yojana subsidy of up to ₹78,000. The central government PM Surya Ghar scheme is strictly restricted to grid-connected (on-grid) residential installations that utilize bi-directional net metering to export surplus electricity back into the state DISCOM distribution network.

Standalone off-grid systems with battery banks do not feed power into the grid and are explicitly excluded from PM Surya Ghar financial assistance. Consequently, an off-grid system must be financed entirely by the property owner. For agricultural water pumping, farmers may explore the PM-KUSUM scheme, which offers designated capital subsidies for standalone solar agriculture pumps. For residential homes with an existing grid connection that experience power cuts, a hybrid solar system is usually far more financially prudent than a pure off-grid configuration.

Regional Solar Hubs

Explore Rooftop Solar by State & City

Calibrated with state Discom tariffs, local net-metering policies, and PM Surya Ghar subsidies across India.

Frequently Asked Questions about Off-Grid Solar in India

Is an off-grid solar system worth the investment in India?

An off-grid system is worth the investment primarily in remote locations, farmhouses, agricultural sheds, rural clinics, and eco-resorts where the utility grid is absent or experiences daily load shedding of 6 hours or more. If you already have a stable grid connection, an on-grid system with net metering or a hybrid system is significantly more economical because batteries roughly double the initial installation cost and require periodic replacement.

How many days of battery autonomy should be planned for an off-grid system?

In most Indian regions with strong annual sunshine, 1 day of battery autonomy is standard for non-critical residential use. In coastal states like Kerala and Maharashtra, or northeastern and Himalayan states that experience prolonged monsoon downpours or heavy winter cloud cover, designing for 1.5 to 2 days of autonomy is necessary to prevent blackout conditions.

Why must an off-grid solar panel array be oversized by 30%?

Solar panels produce peak power for only 4 to 5 hours per day in India. During those sun hours, the array must generate enough energy to run all daytime electrical loads while simultaneously replenishing the battery bank from its overnight discharge. Furthermore, system losses from dust soiling, high summer temperature derating, wiring resistance, and charge controller conversion losses require a 25% to 35% generation buffer.

Can an off-grid solar system run a 1.5-ton inverter air conditioner?

Yes, but it requires substantial solar and battery capacity. A 1.5-ton 5-star inverter AC consumes approximately 1,000 to 1,300 Watts of continuous power. Running it for 8 hours overnight requires 8 to 10 kWh of usable battery storage, which translates to a 48V 300 Ah tubular battery bank (eight 150 Ah batteries) or a 10 kWh lithium pack, paired with a minimum 48V 3.5 kVA or 5 kVA MPPT Solar PCU to handle the compressor starting surge.

What is the maintenance required for tubular batteries versus lithium batteries?

Tubular lead-acid batteries require manual inspection and topping up with distilled water every 3 to 6 months, cleaning of terminal posts to prevent lead sulfate corrosion, and adequate room ventilation to disperse hydrogen gas generated during charging. Lithium LiFePO4 batteries are completely sealed, produce no off-gassing, require zero water topping or maintenance, and integrate an internal Battery Management System (BMS) for automated cell balancing and thermal protection.

What happens if our electricity consumption exceeds the battery bank capacity?

The MPPT Solar PCU has a low-voltage disconnect (LVD) safety threshold. If the battery bank discharges beyond its safe limit, the inverter automatically shuts down AC output to protect the battery cells from permanent sulfation or chemical destruction. For properties with occasional heavy consumption, integrating a dual-source backup such as an auto-start diesel generator or grid charging bypass is recommended.

Are off-grid solar installations eligible for central PM Surya Ghar subsidies?

No. Standalone off-grid systems with battery storage are not covered under the PM Surya Ghar Muft Bijli Yojana. Central subsidies are reserved exclusively for grid-tied rooftop solar systems connected through a net meter.

Before you rely on this estimate

This calculator produces a planning range from your inputs and the assumptions shown on the page. It cannot replace a site visit, roof-shade survey, Discom approval or supplier quotation.

A calculator is not a quotation. A written quote should separately state the module and inverter model, mounting structure, protection equipment, taxes, net-metering work, warranty and completion timeline.

Next step: turn this result into a capacity, roof-space and budget decision.

Calculate system cost →